السلام عليكم ورحمة الله وبركاته
بصراحة لطالما قرات هذا الموضوع في اكثر من منتدى ولم اصدقه او بالأحرى كنت خائف جدا من التجربة وبعد تفكير طويل قررت المحاولة والحمد لله تمت العملية بنجاح وكانت اسهل وابسط مما توقعته وحدثت جوالي 90 الى الفيرجن الأخير في ربع ساعة تقريبا وانصح كل الأعضاء ان يحدثوا جوالاتهم بانفسهم وبدون وكلاء لان العملية والله ما تستاهل فقط كل ما عليك انك تنزل البرامج المطلوبة وتتبع الخطوات خطوة بخطوة وستنجح بإذن الله .
الطريقة باللغة الانجليزية :
1) install Diego. Dont restart the pc after install.
2) open crack.exe but dont install it yet.
3) run phoenix_service_sw_2004_39_7_70.exe
4) you will get msg that you cant continue the installation without nokia dongle.. press retry and immediately press install at the crack program.. setup will continue if you successfully do the crack at the time..
5) when setup continues, you will get some boxes written continue anyway. dont worry, press continue any way. setup will complete and if it asks you to restart, then restart. the pC. After restart the pc will install some files while you get those DESKey error two times, dont worry.. press ok.after completing the installation u will be loged in windows.
6) run Nokia_conn_cable_driver_159_ita.msi wait until its complete..
7) when setup finished, connect your phone through CA-53 or DKU-2 cable.. and wait until its finish install the phone's driver.. it will tell you that 'the device is installed and ready to use.'
then, open phoenix 2004 and minimised it.
If it shows an error like "Nokia dongle not found" than it will not work, u have to unstall erevy thing and reinstall it from frist step.
=====remember to uninstall all the drivers such as dku-5 and others and all the phoenix stuffs like flash update including diego... remove all files related to this via add and remove program.. and clean the registry by tuneup utilities (1-click maintenance)====
9) run phoenix_servise_sw_2006_12_5_136.exe while your phone is connected to the cable. and wait for the dialog "Cannot install Nokia cable driver" there will be three option " About / Retry / Ignore". Click on Ignore. The installation will start. When the installation is finished, It will tells you to restart or not, press restart later.
10) Now maximize the phoenix back and close it..
11) Launch the phoenix back and press help to check the version. You will have the phoenix service 2006...
12) Now close the program Phoenix. Disconnect the cable from the mobile and connect it again.. wait for a while if everything going alright the advice "Your new hardware is installed and ready for usage" (or something like that) are displayed
It may or may not again install some files while you get those DESKey error two times, don’t worry.. press ok. (When I was doing it installs some files)
13) open the phoenix 2006 software: in the Phoenix select:
File > manage connections > new > select the USB tab > next > next > manual setup > USB > apply > close
(You will see that the phone is connected in bottom right corner USB)
14) Click on File> Scan product
15) If you want, you can make a backup, select:
Product>user settings>all settings>backup
If you make a backup you can restore it with the Restore function.
16) Now the Flashing process, select:
Flashing > SW update
Wait for a while bcoz at that time it try to communicate with mobile. When all process is completed u will see like this:--
17) Now U can see that there is box called OPERATING MODE. Select Normal from the box.
Browse for image file and PPM file according to your telephone model
FOR N70:
Code: blank
Image file: Locate the Firmware file *.C0 for N70: RM84_50609201.C0 (This is my one which I have used)
PPM File: Locate the Firmware File *.V084 for N70: RM84_50609201.V084 (This is my one which I have used)
18) Click start, and let the program works it will take 5 min to flash and make it update. At this time don’t ever touch the mobile, it will turn off automatically. Don’t worry at this moment it will do update.
19) When it finished polling, disconnect the cable and restart your telephone...maybe it's all OK!!!
Note: the verifying procedure and polling procedure could not ends well on the N70...but don't worry. Disconnect the cable and switch on the device. (Or open out the battery and sim than put it again and switch it on)
وهذه باللغة العربية :
-اشحن تلفونك للاخر
-امسح من الكمبيوتر Nokia pc suite و Nokia conectivity cable driver !
-نزل من السيت برنامج اسمه DIEGO ثم افتح الفايل المكبوس و اعمل له انستالاشن install
-اذا طلعت لك مسج ***ور معناها انك لم تمسح Nokia conectivity cable driver
-نزل من السيت phoenix 2004 avec crack افتح الفايل المكبوس يطلع لك ملفين ملف ال phoenix و ملف ال crack
-افتح ملف ال crak بدون ما تعمل install
-اعمل انستال للفونيكس phoenix و عندما تاتيك اول مسج ***ور اعمل التالي هذا مهم جدااا
----اكبس على try again و بعدها بسرعة اعمل انستال للكراك crak ----
اذا لم تكن سريع كفاية عليك اعادة العملية الا ان تنجح و تذهب المسج
-و بعدها سوف يطلب منك تعمل رستارت للكمبيوتر فاعمل رستارت
عندما تعمل الرستارت سوف تطلع لك 2 مسج ***ور عادي سدها
-نزل من السايتNokia_Conn_Cable_Driver_159_ita.rarو اعمل انستال install للفايل و ذاذ طلب منك تعمل رستارت للكمبيوتر اعمل
-في كمبيترك سوف تلقي ايكن icon للفونيكس اكبس عليه سوف تطلع لك كم مسج ***ور سكرها عادي
-لا تغلق البرنامج الفونيكس قفط انزله تحت
-نزل من السايت phoenix_service_sw_2005_36_7_112.exe واعمل له انستال setup بدون طبعا غلق الفونيكس
-راح يطلب منك عمل رستارت للكمبيوتر و لكن اكبس على لا -مهم جدا-اكبس على i will restart later
-بعد الانتهاء من الانستالاشين اغلق الفونيكس و افتحه مرة ثانية
-اربط تلفونك بالكمبيتر مع الكابل DKU-2 و اترك ويندوز تحمل الدرايفرز drivers للتلفون
-داخل الفونيكس اعمل
file ? Manage conection ? Add ? Manual ?select USB? Terminer? Aplly et Close .
-الان الفلاش
افتح الفونيكس واذهب الى flashing? sw update
-في اول سطر image file اختار نوع الملف الذي نهايته RM36_5.050407_B5.C0R
-في ثاني سطر PPM File اختار نوع الملف الذي نهايته RM36_5.050407_B5.v30
قبل ما تكبس على فلاش تاكد انه الكابل مربوط جيد بالتلفون و التلفون مشحون
اعمل ستارت start و خلاص
اما انه بالنسبة لفئة N نفس العملية و لاكن عليك استعمال phoenix_service_sw_uploaded by platijet_2006_04_6_130 بدل من phoenix_service_sw_2005_36_7_112.exe
ملاحظة مهمة :
استخدم فونيكس 2005 في حالة 6630,6680,6681 واستخدم فونيكس 2006 في حالة فئة n
البرامج اللازمة :
1:
http://rapidshare.de/files/18927239/...part1.rar.html
http://rapidshare.de/files/18932723/...part2.rar.html
2:
http://rapidshare.de/files/20195369/...crack.rar.html:
3:
http://rapidshare.de/files/6708731/p...part1.rar.html
http://rapidshare.de/files/6710176/p...part2.rar.html
4:
http://www.megaupload.com/fr/?d=YQDG8EU2 فونيكس 2006
5:
http://www.9q9q.net/index.php?f=z5yrSPkg تعريف الكابل
انا حاب انكم تستفيدوا فقط من هذا الموضوع ولا تنسونا من صالح دعائكم .
م ن ق و ل
بصراحة لطالما قرات هذا الموضوع في اكثر من منتدى ولم اصدقه او بالأحرى كنت خائف جدا من التجربة وبعد تفكير طويل قررت المحاولة والحمد لله تمت العملية بنجاح وكانت اسهل وابسط مما توقعته وحدثت جوالي 90 الى الفيرجن الأخير في ربع ساعة تقريبا وانصح كل الأعضاء ان يحدثوا جوالاتهم بانفسهم وبدون وكلاء لان العملية والله ما تستاهل فقط كل ما عليك انك تنزل البرامج المطلوبة وتتبع الخطوات خطوة بخطوة وستنجح بإذن الله .
الطريقة باللغة الانجليزية :
1) install Diego. Dont restart the pc after install.
2) open crack.exe but dont install it yet.
3) run phoenix_service_sw_2004_39_7_70.exe
4) you will get msg that you cant continue the installation without nokia dongle.. press retry and immediately press install at the crack program.. setup will continue if you successfully do the crack at the time..
5) when setup continues, you will get some boxes written continue anyway. dont worry, press continue any way. setup will complete and if it asks you to restart, then restart. the pC. After restart the pc will install some files while you get those DESKey error two times, dont worry.. press ok.after completing the installation u will be loged in windows.
6) run Nokia_conn_cable_driver_159_ita.msi wait until its complete..
7) when setup finished, connect your phone through CA-53 or DKU-2 cable.. and wait until its finish install the phone's driver.. it will tell you that 'the device is installed and ready to use.'
then, open phoenix 2004 and minimised it.
If it shows an error like "Nokia dongle not found" than it will not work, u have to unstall erevy thing and reinstall it from frist step.
=====remember to uninstall all the drivers such as dku-5 and others and all the phoenix stuffs like flash update including diego... remove all files related to this via add and remove program.. and clean the registry by tuneup utilities (1-click maintenance)====
9) run phoenix_servise_sw_2006_12_5_136.exe while your phone is connected to the cable. and wait for the dialog "Cannot install Nokia cable driver" there will be three option " About / Retry / Ignore". Click on Ignore. The installation will start. When the installation is finished, It will tells you to restart or not, press restart later.
10) Now maximize the phoenix back and close it..
11) Launch the phoenix back and press help to check the version. You will have the phoenix service 2006...
12) Now close the program Phoenix. Disconnect the cable from the mobile and connect it again.. wait for a while if everything going alright the advice "Your new hardware is installed and ready for usage" (or something like that) are displayed
It may or may not again install some files while you get those DESKey error two times, don’t worry.. press ok. (When I was doing it installs some files)
13) open the phoenix 2006 software: in the Phoenix select:
File > manage connections > new > select the USB tab > next > next > manual setup > USB > apply > close
(You will see that the phone is connected in bottom right corner USB)
14) Click on File> Scan product
15) If you want, you can make a backup, select:
Product>user settings>all settings>backup
If you make a backup you can restore it with the Restore function.
16) Now the Flashing process, select:
Flashing > SW update
Wait for a while bcoz at that time it try to communicate with mobile. When all process is completed u will see like this:--
17) Now U can see that there is box called OPERATING MODE. Select Normal from the box.
Browse for image file and PPM file according to your telephone model
FOR N70:
Code: blank
Image file: Locate the Firmware file *.C0 for N70: RM84_50609201.C0 (This is my one which I have used)
PPM File: Locate the Firmware File *.V084 for N70: RM84_50609201.V084 (This is my one which I have used)
18) Click start, and let the program works it will take 5 min to flash and make it update. At this time don’t ever touch the mobile, it will turn off automatically. Don’t worry at this moment it will do update.
19) When it finished polling, disconnect the cable and restart your telephone...maybe it's all OK!!!
Note: the verifying procedure and polling procedure could not ends well on the N70...but don't worry. Disconnect the cable and switch on the device. (Or open out the battery and sim than put it again and switch it on)
وهذه باللغة العربية :
-اشحن تلفونك للاخر
-امسح من الكمبيوتر Nokia pc suite و Nokia conectivity cable driver !
-نزل من السيت برنامج اسمه DIEGO ثم افتح الفايل المكبوس و اعمل له انستالاشن install
-اذا طلعت لك مسج ***ور معناها انك لم تمسح Nokia conectivity cable driver
-نزل من السيت phoenix 2004 avec crack افتح الفايل المكبوس يطلع لك ملفين ملف ال phoenix و ملف ال crack
-افتح ملف ال crak بدون ما تعمل install
-اعمل انستال للفونيكس phoenix و عندما تاتيك اول مسج ***ور اعمل التالي هذا مهم جدااا
----اكبس على try again و بعدها بسرعة اعمل انستال للكراك crak ----
اذا لم تكن سريع كفاية عليك اعادة العملية الا ان تنجح و تذهب المسج
-و بعدها سوف يطلب منك تعمل رستارت للكمبيوتر فاعمل رستارت
عندما تعمل الرستارت سوف تطلع لك 2 مسج ***ور عادي سدها
-نزل من السايتNokia_Conn_Cable_Driver_159_ita.rarو اعمل انستال install للفايل و ذاذ طلب منك تعمل رستارت للكمبيوتر اعمل
-في كمبيترك سوف تلقي ايكن icon للفونيكس اكبس عليه سوف تطلع لك كم مسج ***ور سكرها عادي
-لا تغلق البرنامج الفونيكس قفط انزله تحت
-نزل من السايت phoenix_service_sw_2005_36_7_112.exe واعمل له انستال setup بدون طبعا غلق الفونيكس
-راح يطلب منك عمل رستارت للكمبيوتر و لكن اكبس على لا -مهم جدا-اكبس على i will restart later
-بعد الانتهاء من الانستالاشين اغلق الفونيكس و افتحه مرة ثانية
-اربط تلفونك بالكمبيتر مع الكابل DKU-2 و اترك ويندوز تحمل الدرايفرز drivers للتلفون
-داخل الفونيكس اعمل
file ? Manage conection ? Add ? Manual ?select USB? Terminer? Aplly et Close .
-الان الفلاش
افتح الفونيكس واذهب الى flashing? sw update
-في اول سطر image file اختار نوع الملف الذي نهايته RM36_5.050407_B5.C0R
-في ثاني سطر PPM File اختار نوع الملف الذي نهايته RM36_5.050407_B5.v30
قبل ما تكبس على فلاش تاكد انه الكابل مربوط جيد بالتلفون و التلفون مشحون
اعمل ستارت start و خلاص
اما انه بالنسبة لفئة N نفس العملية و لاكن عليك استعمال phoenix_service_sw_uploaded by platijet_2006_04_6_130 بدل من phoenix_service_sw_2005_36_7_112.exe
ملاحظة مهمة :
استخدم فونيكس 2005 في حالة 6630,6680,6681 واستخدم فونيكس 2006 في حالة فئة n
البرامج اللازمة :
1:
http://rapidshare.de/files/18927239/...part1.rar.html
http://rapidshare.de/files/18932723/...part2.rar.html
2:
http://rapidshare.de/files/20195369/...crack.rar.html:
3:
http://rapidshare.de/files/6708731/p...part1.rar.html
http://rapidshare.de/files/6710176/p...part2.rar.html
4:
http://www.megaupload.com/fr/?d=YQDG8EU2 فونيكس 2006
5:
http://www.9q9q.net/index.php?f=z5yrSPkg تعريف الكابل
انا حاب انكم تستفيدوا فقط من هذا الموضوع ولا تنسونا من صالح دعائكم .
م ن ق و ل